Where can I get (the latest) CPS?
From where you bought your radio. Or if you prefer here.
The version of CPS I have gives error code #1057 when I read my new radio?
The firmware version in the radio is newer than that which the CPS can support. You need to update your version of CPS.
When I plug the programming cable into the PC, Windows does not make the 'USB Start' sound?
This is correct, there is no 'intelligence' or level conversion in the programming cable. This will only happen when you connect a radio.
When I connect the radio to my PC, Windows asks for a driver?
As far as I know, Windows 7 and 8 do not have this problem.
This should only occur with Windows XP and 2000. The drivers are not signed and you need to install them manually by selecting 'Have Disk' and pointing to C:Program FilesCommon FilesMotorolaMOTOTRBO Driver. Windows will give a warning when installing this, you can ignore this warning.
When I try to read the radio I get an error code #595?
Error 595 is generally caused by an IP address conflict. When your radio is connected to the PC, Windows sets up a network connection to the radio. The default IP address used for this connection is in the 192.168.10.x range (usually the radio is .1 and your PC is .2).
If you are going to be programming a lot of radios, the easiest solution would be to change the IP address range allocated to your PC on your LAN/WLAN network so that it is not in the same range as the radio.
As soon as I plug the radio into the PC, I loose all network connectivity?
The fix is to allocate a static metric to your LAN/WLAN connection:
Open the Network Connections folder
Right click the LAN or WiFi connection.
Click Properties then go to Internet Protocol Version 4.
Click Properties and go to Advanced.
Un-tick Automatic metric.
Enter a 1 for the Interface metric.
OK; OK; OK..
This seems to occur mostly with Windows 7 PCs. The reason is that Windows is somehow allocating a lower device metric to the MOTOTRBO radio and your PC now thinks it's the new network connection to use.
If this is your only radio, simply change the Radio IP address in the codeplug or just switch off WiFi/unplug the LAN cable when programming your radio.
How do I program my radio?
I've produced a number of tutorial videos and these are available on YouTube.
How do I upgrade my MOTOTRBO radio?
Via the CPS - see this video. It takes about two minutes depending on the model and how good your PC is. Make sure the radio is properly powered during this process and that you don't mistakenly unplug the cable - otherwise you'll understand what some people mean by 'bricked'.
If I clone my radio, the Radio ID is not overwritten?
This can be turned off. Go to Edit>>Preferences and tick Clone Radio Identity..
When I read a new radio, the CPS shows error code #1027 codeplug version not supported?
Like nearly all Motorola radios, your MOTOTRBO radio has a regional ID. Generally speaking, there are two possibilities: either you purchased the radio from another region (i.e. grey market) or have downloaded a (pirate) copy of the CPS from the internet. In either case, you will need to contact the company who sold you this radio and request support from them.
My problem isn't listed here, what now?
If you are a Motorola contractual customer in Europe or Africa, you can contact me directly. Otherwise you'll have to contact the company who sold you your radio. Or contact one of Motorolas' dealers by clicking here.
Nick: I also recently wanted to upload some software to be posted on this site, but once I clicked on the submit button with all the fields filled out, I never got the confirmation page. Maybe the server was busy at the time, but I tried uploading twice without luck.
From where you bought your radio. Or if you prefer here.
The version of CPS I have gives error code #1057 when I read my new radio?
Computer Programming Software. Download the current Motorola CPS. Choose “Save As” and save to a folder or the desktop on the PC. https://projectever265.weebly.com/blog/mondo-rescue-live-cd-download. Find the answers to these questions: How to program a. We are asked many questions centered around Motorola CP200D Programming. https://projectever265.weebly.com/blog/torrent-art-blakey-moanin. Motorola CP200 'CPS' Software.
Sep 19, 2015 - The software would do 'Append' on default, which, in my case. 2 codeplugs in the same APX CPS window (unlike MotoTRBO CPS) and. This forum is for discussions regarding all aspects of Motorola radio programming, including hardware, computers, installation and use of RSS/CPS, firmware upgrades, and troubleshooting. There are subforums for discussions of codeplugs, and also for software/firmware release notes and issues. Nov 30, 2017 - SiteBoss, Motorola CPS software radio programming for Astro & APX. 520 plantronics driver windows 7. Monitoring, problem determination and troubleshooting of Olmsted.
The firmware version in the radio is newer than that which the CPS can support. You need to update your version of CPS.
When I plug the programming cable into the PC, Windows does not make the 'USB Start' sound?
This is correct, there is no 'intelligence' or level conversion in the programming cable. This will only happen when you connect a radio.
When I connect the radio to my PC, Windows asks for a driver?
As far as I know, Windows 7 and 8 do not have this problem.
This should only occur with Windows XP and 2000. The drivers are not signed and you need to install them manually by selecting 'Have Disk' and pointing to C:Program FilesCommon FilesMotorolaMOTOTRBO Driver. Windows will give a warning when installing this, you can ignore this warning.
When I try to read the radio I get an error code #595?
Error 595 is generally caused by an IP address conflict. When your radio is connected to the PC, Windows sets up a network connection to the radio. The default IP address used for this connection is in the 192.168.10.x range (usually the radio is .1 and your PC is .2).
If you are going to be programming a lot of radios, the easiest solution would be to change the IP address range allocated to your PC on your LAN/WLAN network so that it is not in the same range as the radio.
As soon as I plug the radio into the PC, I loose all network connectivity?
The fix is to allocate a static metric to your LAN/WLAN connection:
Open the Network Connections folder
Right click the LAN or WiFi connection.
Click Properties then go to Internet Protocol Version 4.
Click Properties and go to Advanced.
Un-tick Automatic metric.
Enter a 1 for the Interface metric.
OK; OK; OK..
This seems to occur mostly with Windows 7 PCs. The reason is that Windows is somehow allocating a lower device metric to the MOTOTRBO radio and your PC now thinks it's the new network connection to use.
If this is your only radio, simply change the Radio IP address in the codeplug or just switch off WiFi/unplug the LAN cable when programming your radio.
How do I program my radio?
I've produced a number of tutorial videos and these are available on YouTube.
How do I upgrade my MOTOTRBO radio?
Via the CPS - see this video. It takes about two minutes depending on the model and how good your PC is. Make sure the radio is properly powered during this process and that you don't mistakenly unplug the cable - otherwise you'll understand what some people mean by 'bricked'.
If I clone my radio, the Radio ID is not overwritten?
This can be turned off. Go to Edit>>Preferences and tick Clone Radio Identity..
When I read a new radio, the CPS shows error code #1027 codeplug version not supported?
Like nearly all Motorola radios, your MOTOTRBO radio has a regional ID. Generally speaking, there are two possibilities: either you purchased the radio from another region (i.e. grey market) or have downloaded a (pirate) copy of the CPS from the internet. In either case, you will need to contact the company who sold you this radio and request support from them.
My problem isn't listed here, what now?
If you are a Motorola contractual customer in Europe or Africa, you can contact me directly. Otherwise you'll have to contact the company who sold you your radio. Or contact one of Motorolas' dealers by clicking here.
what region is this for need aa version?thanks
Hi friend, is LACR, I have only EMEA. NA i have 12.1
MOTOTRBO 12.1 NA AA
Do you have the link to the NA 12.1?
Hello friend, if I have it but you can not hang external links, I'll upload it and I ask the moderator to approve the upload.
Last edit: by YV5ADM
thanks much!
Create a ticket TYPE: Request for validation once you've uploaded it and I'll test/validate it.
Nick
Nick
Friend LZ2NJG I tried to load the CPS Mototrbo NA version 12.1 and gives me server error. I can send you the link to this and other upload it? I hope your answer to resend.
YV5ADM said
Friend LZ2NJG I tried to load the CPS Mototrbo NA version 12.1 and gives me server error. I can send you the link to this and other upload it? I hope your answer to resend.
Someone already uploaded Version 12.1 Build 645 for Windows. Just search for it here in the Moto CPS section.Nick: I also recently wanted to upload some software to be posted on this site, but once I clicked on the submit button with all the fields filled out, I never got the confirmation page. Maybe the server was busy at the time, but I tried uploading twice without luck.
Build 645
chipichipi said
Someone already uploaded Version 12.1 Build 645 for Windows. Just search for it here in the Moto CPS section.
Nick: I also recently wanted to upload some software to be posted on this site, but once I clicked on the submit button with all the fields filled out, I never got the confirmation page. Maybe the server was busy at the time, but I tried uploading twice without luck.
They uploaded the EMEA version, they didn't upload the NA version, which is what we need. Nick: I also recently wanted to upload some software to be posted on this site, but once I clicked on the submit button with all the fields filled out, I never got the confirmation page. Maybe the server was busy at the time, but I tried uploading twice without luck.
okto said
They uploaded the EMEA version, they didn't upload the NA version, which is what we need.
The AA version is up now. I uploaded it a few days ago. LACR NEWEST VERSION
First thanks everyone for your support
Do you have the newest versión for LACR? I try programming my radio with this versión but the codeplug is not compatible? any suggestion ?
Thanks
Do you have the newest versión for LACR? I try programming my radio with this versión but the codeplug is not compatible? any suggestion ?
Thanks
Ciao
è valido per DP1400?
cp200d
i just got a cp200d from eaby im looking for a softwear for it i need help
Motorola Cps Programming Software Download
cp200d
Motorola Cps Programming
i just got a cp200d from ebay im looking for a softwear for it i need help